RamCharger.net

I have a 2001 Cherokee 2wd that will be converted to 4wd eventually. Looking for a front TJ Rubi 44 if cheap enough or a Dana 30 out of a Cherokee or TJ.

Me and Pam have been discussing it. Don't think we will have anything to wheel in ourselves this time but we probably will go and keep yall company..lol. I'm still having engine problems with my Dodge and tomorrow i'm going to jack with the timing a little. Who know's maybe i'll get lucky. If i can't get it running right it will be for sure in April for a next year trip.

Ok Ron i have to ask, whats a Nambu?? In the next few weeks i should be hauling my truck down from dads place. Hopefully will get started on fixing it soon after. Not sure if i can make something as early as April or May but once the old girl is back up an running i'm down to drive whereever.

What up. Really appreciate yall's 2cents guys. My engine is rebuilt. My tranny also. When i deep sixed the engine water also got in that vent hole at the top of the case behind the torque converter. I removed the tranny while my truck was still chained down on Skip's trailer. Thanks again Skip for being there when i needed help    I carried the loose tranny into a shop and had them plug the factory design vent hole and then tap the top outer case and i now have a long vent line. Kinda like the axle set ups. My plan is to do the following. Now it might seem kinda wastefull i know to buy some things to replace that i'm not even sure will work but maybe i'll get lucky. Shopping list........ New MSD fuel pump from Jegs catalog that will replace the old one, throttle position sensor from dealership, replace the Auto Shut Down relay, New O2 sensor. I will then fire up truck and get my tach working again and then check my idle RPM. That's about all i know to do. After that if it still aint right i'll be taking it to a friend of Skip's shop. I really look forward to this thing running again as it seems i aint been wheelin in years..lol

Appreciate the info about adjusting the idle. I need to hook my tach back up to do this. I've seen how to do this in my Haynes book but I had to go get my manuel to verify something. During the procedure after the engine is (37)warmed up a few minutes. And after you (38)disconnect the idle speed control actuater and the coolant temp sender. (39)Hook up a tach. It states: (40)Start the engine. Adjust the extension screw on the ISC actuator until RPM correct. (41)Reconnect the ISC actuator electrical connection. (42)Reconnect the coolant temperature sensor.  Now heres my problem.....my book doesnt say after you adjust the screw on ISC to "Turn Off Engine", then do steps 41 and 42. I did not mention this before, but i did this procedure by my book without the tach but just listening to engine RPM just to raise it some before trying road trip. I adjusted the screw while the engine was high revving. Then reconnected the ISC then the temp sensor. My idle dropped down after that. Then i turned off engine at some point. Also before my engine rebuild i had bought a ISC thru Oriellys just to change it so i wouldnt have to worry about old stuff on my engine. Not sure the brand of it. Should i just use Dealership stuff when it comes to the ISC actuator and the TPS ?

What up SixGun. When started the truck idles up then slowly idles down. Seems to idle fine. Occasionaly the idle will drop down kinda like a stumble then shoot back up. When i put in into gear its almost like the idle isnt quite high enough. Sometimes it will die out in gear. I can check that once i get my tach hooked back up. I only have about 300 miles on this rebuilt long block. I had asked the shop that did the install if i would be able to get away with any kinda slight RV cam in it. I was told yes. So he put in a Melling MC1263. Google it and check out the specs. I have know idea the specs on the stock factory cam so maybe you will know if the Melling should work ok. I basically two footed the brake/gas to keep it running. Jumped on the highway and seemed to be doing ok. Then the truck kinda stumbled/hickupped then kept going another half mile then just cut out. I drifted over. It fired back up. Took off for another mile then it cut out again. I cranked and cranked till the battery about died but it finally fired up and i turned around and made it home. I had just put 15 gallons of fresh SuperUnleaded in the fuel cell. I think i will check my fuel cell lines and fittings. Make sure there are know pinholes sucking air. Perhaps change the fuel pump just to rule that out. I'm not sure on the actual process of checking the codes with the ignition switch? I may just change the O2 sensor also as i'm not sure how old it is.
 

What up. I'm gonna check a few things myself and perhaps i'll get lucky. The inline MSD pump i installed after the fuel cell is about 4 years old. I'm gonna but a inline fuel pressure gauge and see what's happening. If no go go go i will tow it to a friends mechanic shop. If still no go go go. Then i'm sure they can help me with carb conversion. I've never used a meter     but thanks for the offer    I've changed the various sensors and the pressure regulater already. I'm pretty sure its a fuel problem and i'm not giving up.

What up. Having some issues with my TBI setup. I think it's wiring, everything is almost 25 years old. In case i cant get the TBI working i'm really wanting to go to a simple fuel setup since i dont drive the truck much and as of this January i dont have to emissions test anymore. I just woud like to verify...would an Edelbrock #3776 intake work on my 1989 360 ?  I know it would on 360's that came with carbs from factory. Just not sure on TBI engine's. I plan on useing a MSD 6 ignition box and distributer.

It's cool SixGun  Things have been a little stressfull around here so i kinda vented some. My first RamJam was 2003. Thats where i met Toyradio. He's been in my corner from day one. Skip and his family i couldnt ask for better friends. RJ09 i couldnt compete with Sams big block and 44's. Done a few Tex chapter meets. Was really looking forward to RJ13 but things just didn't work out getting my truck ready in time and of course family always comes first. Looking forward to getting with all yall on the trails down the road 

   Alright so if it wasn't for that link reguarding RAMJAM on RCC I never would have found where everyone went..lol Did I miss something??