RamCharger.net

Toy,  I got a few things you may want for your RC like the springs, I got a 44 and 9.25 out of my 81 the 44 is a hub locking type. let me know
REB

Toy.
I have some old 4 inch Rancho springs of my 81 RC, but are still in good condition.   40 bucks for the pair. I live near the Long Beach, Ca area. Let me know (  SOLD  )
REB

Here is my take on a inline filter for home use, no matter what you need a filter separator for painting, or you paint job will look like crators of the moon and you paint will blister/peel with in 2-4 yrs.  Now as far as air tools, the filter will make you tool last longer, BUT not manditory. Years ago I used to work at several dealerships that had no filter or separator in the system and on some summer days I had a really cool water fountian blowing out my impact gun and air rachet. And even if I oiled the tools it would only last about 3 yrs at a time. Now that I work as the shop mechanic at a body shop, the air is filtered, cooled, and separated, I have no wear, water or any other problems with my tools and its going on year 4. In my opion I would only install a filter if when you drain your compressor tank and more than 2 cups of water comes out of the drain. And always oil your tools before you use them. ATF works in a pinch, but there is inexpensive air tool oil and any hardware store
Hope this helps and good luck
REB

Hey great idea, learn something new every day. Does it work on the large 1 ton chevy truck ujoints? And or any way to make it work on the ujoints on a 4X4 front axle shaft joints?
REB

Hey guys and gals, getting more of my RC left over parts out of the garage and some others, Almost all parts are from a 1981 Ramcharger
Since it looks like I cant or dont know how to post pics just email me at advancedmarketingdiv@yahoo.com   (the addy is to keep spammers away) and I will send pics
1 Rear seat belt buckles
2 Gas tank straps
3 Gas tank fill line and hose
4 Gas tank skid plate
5 Gas tank
6 Transfer case shift boot W/plate
7 Ash tray (red) with light, dont know if light works
8 Brake booster
9 Hood hinges
10 Ebrake pedal assy W/out cable
11 A/C Heater control head, no idea if it works
12 Rear rear leaf spring shackle
13 Non tilt coulm ignition switch
14 Passenger seat pedastal w/ latch assy no floor striker  (Note the 81 dosent fit 87 and up RC, I know the 81 is bigger than the 87 bolt holes dont line up
15  Stearing wheel(s) 2 different styles, they both have the lock ring wire that dont fit my 87 and the steering wheels came out of my 81 and a 85 RC
16 Glove box door
17 Exhaust hangers
18 Rear glass only

Now a few other things I got lying around
1 Western golf cart project
2 Several dixie narco coke machines, parts and complete units
3 250 gal propane tank (empty,needs clean out) for smoker conversion only, yea local pick up only. The postman said he dosent have a stamp big enough for a 600 LBS steel tank
4 Metal ammo box
5 Morter crate, sorry no shells
6 93 jeep grand cherokee 318 engine with computer, has accessories
7 93 AWD jeep grand transfer case
8 83 turbo 400 trans from a 2500 suburban
                                    AND
I am checking out some clips for the large lower moldings on a RC and if they work I will be offering them at $5.00 each where they go for around 8.95 each by other vendors
Also I am looking into a custom bulk purchase of rear hatch glass seal that no one can get. The min order is 3 grand for a thousand feet, Have to verify this and it is for the locking seal just like OEM for the non removable tops. And it will take the lock strip just like the OEM. And more to come, I get a big enough interest I will set up a online store
REB

Hey guys, got the latchs from Crankous, so thanks anyway.

Have you ever put the jeep on a scale, with all that steel its got to weight a lot. Cool project though, been thinking of cutting up my cherokee and doing a complete roll bar body. Saw one on the net and a jeep mag, and your blue looks just like that project, really like it too

Really like those bumpers, got a design, thread or something showing more detail on how it was built
Thanks

I thought I saw an Edelbrock intake offered for a magnum engine that a carb would sit on.

Hey gang, just registered, glad to be at the top of the pyrimid ( haha) and thanks to Mopar daddy, he turned me onto this site.    Ever get that frame off the trailer.  Pass on the word ramcharger.net its ALIVE     

I have rebuilt, replace, and custom made harnesses along with a buddy of mine that is a freekin genius when it comes to wiring, on his 67 chevelle he rewired it in all aerospace grade wires ( all white numbered wires ) me I went color coded on my 71 chevelle  ( hey I am a mopar guy the Chevy was free so I couldn't pass it up, traded it for my first RC ) Anyway, I got the wire from Anaheim wire in Anaheim California. They do have a color coding service, they will paint the tracer color any color on any wire you want, the only draw back is that it is spiral painted on not straight, plus they also have connections to some company's that still have the connectors. Also you can contact M&H electrical fabricators   at    www.wiringharness.com     and last on other cars and trucks including my RC's some of the connectors and even fuse block I have found the factory ones are not up to the task of what I wanted then, so I went to the bone yard stripped out connectors, fuse blocks, and pdc from any car or truck I found that had what I need to do my custom build.
Hope this helps and don't forget, DO NOT skimp on wire crimpers, strippers, tape or anything involved in making a splice or connections, you don't want a electrical problem on the trial because you used duct tape instead of electrical tape

I am looking for the door latchs for a 1987 Ramcharger, the plastic linning around the latch needs to be intact ( yea I know, tall order )  and well under $100.00 each, the guy on e-ba_  wants that much and no way am I paying that much, I will weld the doors shut first, and paint a union jack on the doors
Thanks,
REB