News:

Your new home for car and truck enthusiast to share, learn, and brag.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - crazzywolfie

#826
Projects / Re: Willyreplica from the start...
March 22, 2013, 10:01:44 PM
that thing is looking good. i don't know about the yellow but i guess we will have to wait and see once it is done. i kind of like the green.
#827
Projects / Re: 91 RAMM'D 150
March 22, 2013, 09:58:31 PM
don't you still have the v6 kicking around? if it was running good the Distributor Ignition Pickup out of it should be fine. only 2 or 3 screws holding it in the distributor.
#828
Projects / Re: 91 RAMM'D 150
March 22, 2013, 07:33:09 PM
rock auto says the 3.9 and 5.2 use the same hall effects sensor. could maybe try swapping the good one from your 3.9 into the 5.2. could also check the hall effects while you have the sensor out.
#829
Projects / Re: 91 RAMM'D 150
March 22, 2013, 12:39:28 AM
could try checking the old spark plug wires with a digital multi meter. i think there is suppose to be about 12ohm's or less of resistance.
#830
Projects / Re: 91 RAMM'D 150
March 19, 2013, 03:41:41 AM
1283663810490443. this code is suppose to be good till march 24th. hopefully someone on dodge forum will post a new code.
#831
e-fans eh? what did you take them out of? definitely might have to do up a review. i know the rads on the newer rams seem to be a bit smaller so i am not sure if caravan fans would fit. i do know someone on rcc said the caravan fan he got pulled air better than the 3000cfm fan he bought.
#832
maybe you and your ride will end up on power block one day. it has definitely come a long way and is becoming one cool ride that is power block worthy once it is done.
#833
Projects / Re: 91 RAMM'D 150
March 12, 2013, 01:57:33 PM
you know your not suppose to crank those o2 sensors in there tight? the instructions that came with my o2 sensor said something about finger tight. also if you have problems with it in the future you may want to replace it with a NTK which according to rockauto is the OE Mfg. can't beat using OE parts when they are not too expensive.

also glad to here it is running and getting closer to being done.
#834
Projects / Re: what to do. (to good to crush)
March 06, 2013, 09:47:32 AM
maybe if there is no rust you could try selling it on craigs list or something like that. someone might be interested in it.
#835
Projects / Re: 93 RC Trail Rig
February 28, 2013, 10:27:28 PM
that valve looks pretty bad.
#836
Projects / Re: 91 RAMM'D 150
February 24, 2013, 02:29:47 PM
i don't think i would want to run those ford fans. they don't cover enough area and there is only one of them. if it fails you may be left with  no fan. with the dual fan setup you always have at least one fan that can pull air. plus i think those ford fans draw a crap load of power. i don't know exactly how much power the caravan fan draws but i guessed they draw about 20 together while running. i know i have not burned up any relays yet with it yet.
#837
Projects / Re: 91 RAMM'D 150
February 24, 2013, 12:03:02 AM
i think one day you might have to take the gamble. 77440Wagon on RCC got a dual electric fan setup off a 2005 caravan and he said they cool his 440 better than the 3000cfm fan he had before.
#838
Projects / Re: 91 RAMM'D 150
February 23, 2013, 11:00:14 PM
i just got a dual fan setup out of a 2000 caravan in my 81 almost looks like it came from the factory with them. picked it up with a power distribution center at the local junk yard for $40. at the time $40 was worth the gamble especially when you compare it to some of those $200+ setups some people buy. 
#839
Projects / Re: 91 RAMM'D 150
February 23, 2013, 09:47:24 PM
if you had electric fans you wouldn't have to worry about that.
#840
General Discussion / Re: Random pictures
February 23, 2013, 12:10:07 PM