News:

Your new home for car and truck enthusiast to share, learn, and brag.

Main Menu
Menu

Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Show posts Menu

Messages - mopar_daddy

#2
What am I missing? That looks like a 94 and later 241.
Here is the set up I have on my 91 241 cost me a total of 160.00 bucks
#3
General Discussion / Re: Has it occured to anyone else
December 01, 2012, 01:00:07 AM
I have several sets of tools just for that very reason, hell one set goes with me just about every where I go :steeringwheel:. Never know when you might stumble across a good JY it has paid off a few times :headbang:.
#4
General Discussion / Re: Look what I found ...
November 11, 2012, 08:19:02 PM
Nice find  :thumbsup:
A little pricey but the 93's are so nice to drive. Magnum 5.9 and an auto OD good combo.
#5
Projects / Re: Cummins Ramburban
November 11, 2012, 08:13:58 PM
I just picked up an NV 4500 for the project. The auto OD unit was tired and I found the NV for cheap :dance:
#6
General Discussion / Re: Has it occured to anyone else
November 06, 2012, 08:29:28 PM
Quote from: SoCal on November 06, 2012, 05:35:10 PM
Reading this thread made me clean up some of my garage on Sunday. The wife came outside after I had been in there a couple of hours to check on me. She thought I was sick because I was cleaning it out.
OTFLMAO.So you now have room for some of my crap? This type of behavior makes me look bad. Stop it!
#7
Projects / Re: 91 RAMM'D 150
November 04, 2012, 11:07:15 AM
Quote from: SixGun on October 30, 2012, 07:03:01 PM
I wish I could find some big block brackets for that price for the RC.  They are over a $100 online.  Anyone got some??

I've also got the bb truck oilpan and pickup if you are in need of those items as well.
#8
Vehicle Help / Re: TBI stalling issue.
November 03, 2012, 11:23:29 PM
Just for shits and giggles try down shifting it to make sure its not a valve body problem. Maybe sticking in second until complete stoped?
#9
 It's my camera phone doing it justice.I have three and will be using some parts off this one.It has some rust in the front fenders and some one butched the floor/firewall to get at the trans bolts :icon_scratch:. If I didn't need a 1/4 panel and rear glass i would love for someone to save it from me. I saved it from getting crushed.
#10
Here is a pic.
#11
Vehicle Help / Re: TBI stalling issue.
November 03, 2012, 05:27:26 PM
I would inspect the wire loom and make sure the vss has a good signal ground. Also inspect your kick down linkage and make sure the return springs are intact and pulling the TV closed at an idle.
#12
Projects / Re: 93 RC Trail Rig
November 02, 2012, 08:13:40 PM
I've got a complete 93 RC under dash loom and hatch/door locks if your in need of those items.
#13
General Discussion / Re: It never ends....
October 31, 2012, 10:32:12 PM
 :icon_scratch:What caused you to loose that much oil? That thing had to look like a steam train going down the road
#14
General Discussion / Re: It never ends....
October 31, 2012, 07:46:23 PM
Story of my life. >:(
#15
Projects / Re: 91 RAMM'D 150
October 30, 2012, 07:57:18 PM
I've got a set. I'll pull em and get a shipping quote. Been quite busy. I will get you a quote on those springs as soon as I can ;D